TensileProperty相关论文
Multi-principal element alloys usually exhibit outstanding strength and toughness at cryogenic tempera-tures,especially ......
分别在650、750、850℃热处理条件下,研究了高温合金GH4169在75Na2SO4+25NaCl(质量分数)熔盐环境下的热腐蚀行为,之后进行组织表征......
The Mg-8Sn-4Zn-2Al (TZA842,in wt％) alloys with different initial microstructure (as-cast-AC and homogenization treatment-......
Microstructure and Mechanical Properties of Cold Metal Transfer Welding Similar and Dissimilar Alumi
...
Effect of Nano-silica Modification on the Tensile Property of SMA/GF/CF/Epoxy Super Hybrid Woven Fab
Tensile properties of epoxy casts together with shape memory alloy (SMA), glass (GF) and carbon (CF) woven fabric reinfo......
The excellent mechanical performance of oxide dispersion strengthened(ODS)steels is attributed to the highly dispersed a......
In this paper,the effect of sample size and strain rate on tensile properties of titanium alloy was studied.The result s......
Nickel-copper based fibers with 0.11 mm and 0.10 mm diameter,respectively,were produced using a cold drawing process fro......
The purpose of this study is to investigate the effect of wood particle size on mechanical properties of thermoplastic c......
采用高沉积率激光熔覆沉积技术制备了GH4169合金试样, 研究了沉积率为2.2 kg/h时GH4169合金的微观组织和拉伸断裂机制。结果表明：高......
Wood plastic composites (WPC) are composite materials which consist of wood flour and thermoplastics.WPC have been a......
Influence of laser shock peening on surface integrity and tensile property of high strength low allo
Laser Shock Peening(LSP)is a well-established surface treatment commonly used to improve mechanical properties of materi......
Designing new work-hardenable ductile Ti-based multilayered bulk metallic glass composites with ex-s
To overcome the trade-offbetween the devisable microstructure and the excellent tensile ductility of bulk metallic glass......
开发制备了一种汽车用含0.5％Nb(质量分数)的Fe-28Mn-10Al-C-0.5Nb 低密度钢,旨在研究Nb 在奥氏体Fe-Mn-Al-C低密度钢中的存在形态,......
采用共混方法制备了纳米ZnO/HDPE复合材料.研究了纳米ZnO对复合材料力学性能的影响.结果表明:对于经偶联剂表面处理的纳米ZnO,当质......
通过拉伸试验研究了４２ＣｒＭｏ钢热处理制度对光滑试样和缺口试样拉伸性能的影响。结果表明：８５０℃淬火后，５６０℃回火时，４２ＣｒＭｏ钢获得最好的强度和塑韧性配合；该......
研究了高碳Ｓｉ－Ｍｎ系（Ｔｒａｎｓｆｏｒｍａｔｉｏｎ－Ｉｎｄｕｃｅｄ Ｐｌａｓｔｉｃｉｔｙ（ＴＲＩＰ）钢的控冷热处理工艺（油冷至一定温度＋空气炉等温）对拉伸性能的影响。结果表明：控冷后得到了高的强度（σｂ＝１１６０￣１５３０ＭＰａ）和良好的塑性（δ５＝１４％￣２６％）。......
在９００℃到１０５０℃温度范围内采用多道次、大坟下量技术制备Ｑ２３５钢薄板，讨论了轧制工艺、显微组织与力学性能间的关系，并分析了轧后低温退火自理对......
对PBO纤维的干纱、复丝以及单向复合材料的拉伸性能进行实验测试,探讨了测试标准对PBO复丝性能的影响,采用SEM观察了PBO纤维表面形......
通过对比分析两组Ｆ１５５环氧树脂的拉伸性能与其微观结构的关系，探讨了第二相颗料到地其拉伸性能的影响。结果表明，Ｆ１５５环氧树脂的增韧主要是通......
